Electronic cabinet lock with RFID and password access, touch keyboard for easy use.

A smart digital RFID password lock with touch keyboard for securing cabinets and wardrobes.

Smart cabinet lock Enjoy the convenience brought by technology 1. Welcome to use After installing the electronic cabinet lock, please buy four NO.7 alkaline batteries to put them into lock body, and enter the password for on/off lock testing, To avoid abnormal operation causing the system to fail to open the cabinet door. Factory management password: “0000”, please change the management password in time and keep it properly.2. Built in three unlocking modes, you can set the unlocking mode according to the use occasion of the cabinet. 1) Private mode (permanent password unlocking mode) Unlock ： Enter the correct password and press "OK " key to unlock. When the green light is on, the cabinet door can be opened outwark.( Purchasing the card reader version can be configured with card unlocking) Locking ：When the locking tongue is extended, the cabinet door can be locked by closing the door.Factory mode, refer to the sixth point of this document [System Settings] NO.5 instruction. 2) Public mode (temporary password unlocking mode) Unlocking ：Enter the correct password and press "OK " to unlock. When the green light is on, the cabinet door can be opened outward. ( Purchasing the card reader version can be configured with card unlocking)Locking ：When the cabinet lock is in the open state (the lock tongue retracts into the lock body), the customer can set a temporary password to lock it. Enter a 4 ~ 15 digit number and press the "ok " key. When the green light flashes, enter the password again and press the "ok " key to confirm. The lock tongue is extended and the cabinet door can be locked. Enter the temporary password when you need to unlock ( Purchasing the card reader version can be configured with card unlockingLocking ：When the cabinet lock is in the open state (the lock tongue retracts into the lock body), the customer can set a temporary password to lock it. Enter a 4 ~ 15 digit number and press the "ok " key. When the green light flashes, enter the password again and press the "ok " key to confirm. The lock tongue is extended and the cabinet door can be locked. Enter the temporary password when you need to unlock ( Purchasing the card reader version can be configured with card unlocking)Refer to the introduction of the sixth point of this document [system settings]No.4, and input the mode command to For Switch. 3) High security mode (double verification unlocking mode) Unlocking ：Enter the passwork added in advance and press OK. After the first unlocking key passes the verification, the green light flashes.During this period, input the second unlocking key. After the key passes the verification, the unlocking is completed. When the green light is on, the cabinet door can be opened outward. (the card reader version can be combined with different key types of the card / password) the management password is limited to the direct unlocking. Locking ：when the locking tongue is extended, the cabinet door can be locked.Refer to the introduction of the sixth point of this document [system settings]No.6, and input the mode command to For Switch. 3. Change password The management password and user password are composed of 4-15 digits, and you can modify it by yourself if you have old password.The management password is saved by the administrator and used to set the cabinet lock and standby unlocking. (For distinguish, there will be a period of time "do re mi ~ unlock prompt tone" appear when unlocking by the management password, and a short sound will be emitted if by other keys.)1) User password modification operation: Press the "OK" key twice continuously (when the green light flashes) → enter the old user password and press OK → enter the new user password and press OK → to confirm the new user password again, and press OK2) Management password modification: Long press the "OK" key (when the green light flashes) → enter the old management password and press OK → enter the new management password and press OK → to confirm the new management password again and press OK (Factory default 0000)The premise of the above operation is to verify the old password and then set the new password. If "red flashing" occurs during the operation, it indicates that the modification has failed. Analysis: 1. Please distinguish between management password and user password change description. 2. The old password entered is correct. 3. The new password has been verified twice. 4. The password length is within 15 digits.4. System initialization Restore factory settings in the current mode. Initialization operation: Wen t he cabinet lock is powered off, press the "set " key of the lock body and do not release it. At the same time, the installation battery is energized. At this time, the red light on the keyboard is on for 1s, and the system completes initialization.5. Low voltage tips When the dry battery voltage of the lock body is lower than 4.8V, each unlocking will trigger three groups of sounds, accompanied by the low-voltage prompt of red light flashing. The subsequent unlocking is about 200 times. Please replace the internal battery as soon as possible.6. System settings 1.Volume Setting Enter "c1ok" and verify the management password and press "OK ". When the green light flashes, press 1 to decrease the volume, and press 3 to increase the volume. 2. Keyboard light Enter "c2ok" and verify the management password and press "OK ". " Di" is on and "didi " is off.3. Burglar alarm tone Enter "c3ok" and verify the management password and press "OK ". " Di" is on and "didi" is off. ( Note: after this function is turned on, when the system is locked, the alarm will sound for 30 seconds.)4.For Switch public mode Enter the C4ok management password. The green light is on. ( Note: In this mode, the cabinet door is usually open, and guests need to set a temporary password to lock it. After unlocking, the password will become invalid, and it is generally used for mobile or one-time users)5.For Switch private mode Enter "c5ok" and verify the management password and press "OK ", the setting is successful, and the green light will be on( Note: in this mode, after unlocking for 3 seconds, the lock tongue will automatically extended, and the cabinet door can be locked after closing. In addition, manual extension can also be set: when the unlocking green light is on, press the "0 " key for 3seconds, and the lock tongue will remain in this state to avoid repeated unlocking during work and improve work efficiency. When get off work, press "OK " to extend the lock tongue.Attached with cabinet lock status prompt effect, the 8th point of the operation list can be turned on or off.6. For Switch dual key unlocking mode Enter "c6ok" and verify the management password, then press "OK ", the setting is successful, and the green light will be on( Note: this mode requires a combination of two secret keys to unlock, except for the management password)7.Virtual password Enter "c7ok" and verify the management password and press "OK ". " Di" is on and "didi " is off. ( Note: after this function is enabled, it can be unlocked as long as the entered number contains the correct unlocking password. For example, the factory password 0000, input: 1230000321, except the correct password 0000, the rest are virtual passwords. The virtual password can be randomly entered with 30 digits to prevent thieves from peeping at the correct password.)8.Cabinet door lock status prompt Enter "c8ok" and verify the management password and press "OK ". " Di" is on and "didi" is off.( Note: after opening, the prompt light flashes to warn the status of the cabinet door lock)9.Add user password / card Enter "c0ok " and verify the administrative password, then press "OK ". When the green light flashes, key in the new password and press OK. Verify the new password again and press OK. You can add 10 different passwords with a length of 4-15 digits. (These keys coexist in the public mode. Internal personnel are assigned to manage the password cabinet to solve the problem of guests forgetting the password and cleaning the cabinet door.)Enter "c0ok " and verify the management password, then press "OK ". When the green light flashes, put the card near the identification area, and 10 cards can be added continuously. (These keys coexist in the public mode. Internal personnel are assigned to manage the password cabinet to solve the problem of guests forgetting the password and cleaning the cabinet door.)10.Delete user password Enter "c31ok " and verify the management password, then press "OK ", and the green light will be on after deleting all passwords. 11.Delete card Enter "c32ok " and verify the management password, then press "OK ", and the green light will be on after deleting all cards.